1.Bench vise is classified by
– width of the jaw
2.Central head of a combination set is to –
3.2 surface 90º and 45º
4.To scribe a line parallel to the edge
– hermaphrodite caliper
5.Aircraft brake fire must be extinguished with
– dry powder
6.To tow nose wheel steering system, it is essential to –
a)ensure nose wheel steering system is fully pressurized
b)ensure nose wheel steering system disconnect
c)ensure centralizer engaged
7.Class C fire is
– electrical fire
8.Procedure to jack aircraft to a level position
– jacking laterally, longitudinally then recheck laterally
9.ATA chapter for ‘servicing’
–ATA 12
10.Drawing must be drawn according to standard
– BS 308
11.Pictorial view
– isometric
12.Minimum rivet to the edge
– 2D
13.Dimensional inspection of bearing on rocker arm –
a)depth gauge and micrometer
b)telescopic gauge and micrometer
c)‘thickness’ and push fit arbor
14.Maintenance to restore the item to satisfactory condition –
a)prevention maintenance
b)corrective maintenance
15.Major and minor modification is depends on
– effect on the airframe and powerplant
16.Purpose of the continuity check –
a)check the continuity of electrical circuit
b)check the resistance value of electrical circuit
17.Tubing bend
– to prevent excessive stress on tubing
18.Tubing
– not in the heel of the bend
19.Vernier micrometer
– 0.0001
20.What is allowance –
21.1.5” of shaft, 1.449” of hole
– push fit
22.Clearance –
23.Tap for finishing
– plug tap
24.Refueling cannot be carried out when –
a)within 30m (100ft)
b)radar functioning
25.Inspection hole of turnbuckle
– safety of turnbuckle
26.Bearing prepacked with anti freeze grease
– rejected
27.Rivet clearance
– different of diameter hole and rivet
28.1st angle projection
– plan view below front view
29.Thimble in micrometer
– 50
30.Fire extinguisher for magnesium metal fire
– carbon tetrachloride
31.References used for lubrication
– maintenance manual
32.Chemical fluid to clean up bearing
– white spirit
33.Type of drawing where both side are the same
– symmetrical drawing
34.Skydrol get into the eyes
– wash immediately
35.Tolerance –
36.Schematic diagram
– wiring
37.To show relationship of 2 or more parts and subordinate assemblies
– assembly drawing
38.On an inch micrometer, one revolution of thimble from zero point reading will produce
– a gap of 0.025 between anvil and spindle
39.Pliers are classified by
– type and overall length
40.Pliers are used to
– grip small objects
41.Vee block is used to
– hold round work for laying out
42.Insulation test –
a)resistance of insulator
b)resistance of resistor
c)high current
43.Bonding wire
– control surface are interfered
44.Not to exceed 0.003 ohm
45.Less than 75 wires or 1 ½ to 2 inch in diameter
46.Hammer is classified by –
a)width of jaw
b)the weight
c)brand
47.If a mallet is used to tap bolt into a hole, then it is considered to be –
48.To remove a bearing, it is permissible to use –
49.Sagging is a process of –
Essay:-
1.a)What is abnormal event report?
b)Check to be conducted due to heavy landing.
2.Short notes on
a) lead of a screw thread
b) swaging
c) bonded store
c) ATA 100
d) de-icer boot
3.5 defects on the following parts
a)control cable
b)bearing
c)rivet plate
4.List the process of crimping using terminal lug
0 comments:
Post a Comment